DAC Worldwide’s training systems are designed to provide a realistic, hands-on learning experience in a variety of industrial sectors. Each system has the look and feel of real equipment learners might encounter on the job. Built with full-size, industrial-quality components, as well as high-durability, powder-coated surfaces throughout, DAC Worldwide's training systems allow for repeated use and rough handling.
Simlog Mobile Crane Personal Simulator's Pick, Lift, and Place Module has trainees configure the boom angle, extension mode, and length and then place the hook in the rigging target (blue sphere) above the load. Once triggered, lift the load and place it into the target. Each trial ends when the load is sufficiently well placed (the target will turn green), the speed of the load is sufficiently small, and the operator activates the horn.
Simlog Mobile Crane Personal Simulator's Signaling Module has trainees move a load to a target destination hidden from the view of the crane operator, and so a signal person is required.
The signal person must view the lift using the dedicated signal-person display and provide hand or voice signals to the crane operator to safely move the load into the target (the target changes color as the load gets closer).
Each trial ends when the load is sufficiently well placed (the target will turn green), the speed of the load is sufficiently small, and the crane operator activates the horn. Telescope extend/retract control is disabled for this module.
Advanced Edition features lift planning exercises that require a solid understanding of load charts and Signal Person training, i.e. learning to provide appropriate signals to the crane operator (to complete a lift), while at the same time teaching that crane operator to understand and follow those signals.
Simlog Off-Highway Truck Personal Simulator's Corridor Driving 1 Module has trainees drive the truck through the corridor to the target. Each trial ends when the truck is over the target and parked (gear in Park, or gear in Neutral with parking brake engaged).
Simlog Off-Highway Truck Personal Simulator's Complete Haul Cycle 2 Module has trainees drive the truck from the dumping zone to the wheel loader. After the truck is fully loaded by the loader, return the dumping zone, dump the load and drive away.
Simlog's Reach Lift Truck Personal Simulator: Slalom 1 Forward Driving - pick up the load, drive forward through the slalom course, and place the load on the floor at the target position defined by a red outline.
Simlog's Reach Lift Truck Personal Simulator: Slalom 2 - Pick up the load, drive in reverse through the slalom course, and place the load on the floor at the target position defined by a red outline.
Simlog's Reach Lift Truck Personal Simulator: Selective Pallet Racks 2, Standard Aisles - Working with selective pallet racks, pick up each marked load and place it at its target position, using the overhead map for guidance. The loads and their target positions are mixed among the various heights of rack shelves.
Simlog's Reach Lift Truck Personal Simulator: Selective Pallet Racks, Narrow Aisles - working with selective pallet racks, pick up each marked load and place it at its target position, using the overhead map for guidance. The loads and their target positions are mixed among the various heights of rack shelves.
Simlog Mining Truck Personal Simulator - Corridor Driving Module: Trainees drive the truck through the corridor to the target. The trial ends when the truck is over the target and parked (gear in Park or Neutral with parking brake engaged).
Simlog Mining Truck Personal Simulator - Complete Haul Cycle 1 Module: Trainees drive the truck from the dumping zone to the rope shovel and position the truck under the dipper (the shovel's horn will sound when the truck is appropriately positioned).
After the truck has been fully loaded (the shovel's horn will sound when the loading is complete), return to the dumping zone, dump the load and drive away.
Pages
-
-
Item Number:491-000DAC Worlwide’s Transformer Connections Training System (491-000) replicates the conditions and circumstances that a utility worker encounters when making common transformer connections in the field. -
Item Number:408-000DAC Worldwide’s Transformer Wiring Training System (408-000) is a realistic training device that replicates the conditions and circumstances that an electrical worker encounters when making common power transformer connections in the field and industry. This self-contained, tabletop training system provides a safe, inexpensive, yet realistic alternative to paper-based learning without the danger of full-voltage field experience.
-
The Acron Aviation TranSim™ truck driving simulator delivers immersive, risk-free training for commercial drivers. Explore over 125+ training scenarios, realistic vehicle dynamics, and performance feedback with Replay Studio™. -
The Acron Aviation TransitSim™ Bus Simulator delivers realistic training for transit operators, reinforcing core bus-driving skills in a risk-free environment with immersive visuals and Replay Studio™ review tools. -
Item Number:295-723DAC Worldwide's Treater Dump Valve Cutaway (295-723) is a sectioned industrial specialty oilfield valve for training in the operation, construction, and maintenance of on-off type dump valves. -
The primary goal of this course is to teach workers safe procedures for working in and around a trench environment on a construction site. Hard Hat VR's Trenching and Excavation Simulation is ideal for future employees or supervisors who will work in or around trenches on construction sites. -
Item Number:CO3221-7DTo prepare students for electrification of the powertrain in commercial vehicles, the renowned HV training system for passenger cars from Lucas-Nülle has been modified and adapted. The special learning concept of the training system, which combines theoretical and practical content in a target group-oriented manner, enables flexible on-site implementation that is taking regional, operational, and industry-specific features into account. -
Item Number:CO3221-7FThis training system from the TruckTrain series focuses on the topic of "Smart Farming 4.0" based on the ISO bus. Special attention is paid to the function of "Precision Farming with Section Control", which is implemented in the hardware in a practical and interactive way. -
A compact 2-axis CNC Lathe with totally enclosed high-visibility interlocking guard, suitable for all levels of education and training. Programmable spindle speeds and feedrates make the Turn 270 PRO ideal for cutting a range of resistant materials such as wax, plastic, acrylic, free cutting alloys, aluminum and steel.
